Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Abatement Technologies Duct Sealing in Fort Worth: What to Know First
Duct sealing on an Abatement Technologies system in Fort Worth typically runs $450 – $1,200 depending on access, how many leaks we find, and whether mastic alone gets it done or we need to replace failing sections. Most jobs wrap up in a single visit, usually half a day for a full system. We quote a written price before any work starts, and that number does not move at the door.
This page is for homeowners who own a home with Abatement Technologies duct components and want a straight answer on why their ducts are leaking, what it costs to fix, and who in Fort Worth actually knows the equipment. If that’s you, call (682) 255-2572 and Roy or one of the techs will talk you through it.
How Abatement Technologies Products Fail – and How We Fix Them
- Duct board joints on older Abatement Technologies plenum installations. We see plenty of Abatement Technologies fiberglass duct board plenums in Fort Worth homes built in the 1990s and early 2000s. The factory tape Abatement used on those seams dries out after 15+ years of North Texas heat, and the joints start breathing. We remove the failed tape, clean the joint edges, and apply a fiberglass-reinforced mastic rated for duct board. That repair holds for years, not months.
- Collar connections where flex duct meets the trunk line. On many Abatement Technologies layouts, especially in attic installations we service across Arlington Heights and the TCU area, the takeoff collars weren’t sealed properly at initial install. Air bleeds into the attic before it ever reaches the register. We seal each collar with mastic and retape with UL 181-rated foil tape where needed.
- Flex duct compression and kinking at Abatement Technologies registers. We regularly find flex runs that were left too long and then crushed when the homeowner stored boxes in the attic. A kinked run isn’t an equipment failure, but it acts like a leak: the room never gets comfortable. We shorten and reattach the run, then seal the connection.
- Mastic breakdown in unconditioned attics. Abatement Technologies systems use standard mastics and tapes on metal duct seams. In a Fort Worth attic that hits 140°F in August, low-grade tape fails within a few summers. We replace it with mastic that’s actually intended for high-heat attic exposure, not whatever the last crew had in the truck.
- Loose end cap fittings on supply trunks. End caps on rectangular metal trunks, which we see in a lot of Abatement Technologies installations in older ranch homes near the Stockyards, pop loose over time. It’s a simple fix: clean the metal, reseat the cap, and seal with mastic and mechanical fasteners. But left alone, it’s a steady stream of conditioned air into the attic.
Styles & brands we work with
Our Abatement Technologies Duct Sealing Process
- 1
Call and schedule. A live person answers at (682) 255-2572. We set a window, and we show up inside it.
- 2
Walk the system. We inspect every accessible section: the plenum, the trunk lines, each takeoff collar, returns, and the register connections. We use a manometer to see how much static pressure the system is carrying versus what it should be.
- 3
Diagnose in plain terms. We show you exactly where the leaks are and explain what’s happening. No mystery, no scare tactics. You decide what gets fixed.
- 4
Write the price. Before any tool comes out of the truck, you get a written quote. That’s the number on the invoice, period.
- 5
Seal and test. We apply mastic and tape where needed, fix connections, and run the system to verify pressure changed. We clean up the work area before we leave.
- 6
365-Day Done Right Promise. Every Abatement Technologies duct sealing job we do in Fort Worth is covered in writing for a full year. If a seal fails, we come back at no charge. No fine print.
See the difference
Before
After
Before
After
Before
AfterWhat Abatement Technologies Duct Sealing Costs in Fort Worth
Here’s where honest numbers land for Abatement Technologies duct sealing work in Fort Worth:
- Single-location repair – one leaky collar, one failed seam, or one disconnected flex run: $85 – $175.
- Partial system sealing – sealing the plenum and a handful of trunk connections in a typical attic: $350 – $600.
- Full-system duct sealing – every accessible seam, collar, and end cap on a 2,000-square-foot home: $700 – $1,200.
What moves the price is access (crawlspace vs. attic), how bad the existing tape or mastic is, and how many runs need attention. We don’t charge per vent, and we don’t add a surprise disposal fee at the end. Call (682) 255-2572 for a free estimate with a written price before we touch anything.
Why Fort Worth Homeowners Call Hollis Air Duct Fort Worth for Abatement Technologies Work
We’re an independent Abatement Technologies service provider. That means we got to know this equipment the way you learn it: by seeing it installed, failing, and getting fixed across hundreds of homes in Fort Worth. Roy Castellanos has worked duct systems across this city for the better part of two decades, and he’s seen every way a North Texas attic can punish duct work.
We carry quality aftermarket sealing materials that match or beat the factory supplies, and we know when an OEM part is actually worth paying for instead. Since we also service duct systems built around Lennox, Trane, and Carrier equipment, we understand how your Abatement Technologies ducts interact with whatever air handler you’ve got. Every job gets a written price before work starts. Every technician is background-checked and uniformed. The phone gets answered by a person, 24/7. And the 365-Day Done Right Promise means if our seal doesn’t hold, you’re not paying to have it redone. That’s how we handle Abatement Technologies sealing work in Fort Worth, and it’s why our customers tend not to worry about the second visit.
Clean ducts don’t advertise themselves, but dirty ones will.
FAQs
No, sealing your ducts won’t void a manufacturer’s warranty. We use mastic and UL 181-rated materials that are standard across the trade. What voids warranties is using the wrong repair method or slapping tape over a failing seal without cleaning the surface first. That’s exactly what we don’t do.
Most single-location repairs like a disconnected collar or a failed seam are done in one visit, usually one to three hours. Full-system sealing takes half a day. We’ll tell you on the phone what your situation looks like before we schedule. Call (682) 255-2572 and describe what you’re seeing.
If the ducts are structurally sound, sealing is the cheaper and faster fix by a wide margin. We only recommend replacing sections when the duct board has failed, the metal is rusted through, or a run has been crushed beyond repair. We’ll show you the condition and let you decide with a written price either way.
Rooms that never reach temperature, higher electric bills in July and August, and dust showing up on registers a week after cleaning are the three telltale signs in Fort Worth. A pressure test during our inspection confirms it in about twenty minutes. No guesswork.
Because our price is the real price. We don’t bait with a $99 special and then “find” a reason it doubled once the tech is in your attic. The number we write down before work starts is the number on your invoice, and the work is covered for a year. You’re paying for the repair, not for a game. Call (682) 255-2572 if you want a real estimate.
Written by Roy Castellanos, Owner, Hollis Air Duct Fort Worth at Hollis Air Duct Fort Worth, serving Fort Worth and nearby areas.